96-02 3rd Gen 4Runner Extended Rear Bumpstops 0-2 Inch Lift (3.5 Inch)

Regular Price $239.99
Sale Price $239.99 Regular Price
Sale Sold Out
Unit price
Shipping calculated at checkout.
This is a pre order item. We will ship it when it comes in stock.
Vendor DuroBumps


DuroBumps provide smooth, progressive dampening that greatly reduces hard bottom-outs, allowing for more control and comfort compared to OEM bump stops that feel rock-hard on contact.

DuroBumps are proudly made in the USA with dual durometer (hardness) rubber, eliminating the shell-shock effect experienced with OEM bump stops.

The DuroBumps DBR354R is designed to be slightly taller than OEM bump stops because DuroBumps compress under load to deaden impact just prior to the ultimate stop. The DBR354R will not limit your wheel-up travel compared to OEM bump stops. It is intended for stock-height trucks and mild lifts up to 2 inch (fully loaded).
(For lifts of 2 inch or more, we offer a 5.25 inch version)
Features and benefits

  • Improved handling - Dual durometer rubber allows DuroBumps to act as a secondary coil spring, with smooth engagement that progressively increases compression load in a predictable fashion.
  • Mounts in OEM location - Easily bolts into the OEM location, ensuring a proper fit with no modifications.
  • No loss of up travel - Direct OEM replacement, with no loss of suspension/wheel-up travel.
  • Increased suspension life - Greatly extends the service life of other suspension components by absorbing the shock load from suspension bottom-outs. DuroBumps absorb the impact, saving critical suspension components from excessive wear and extending service intervals for shocks, upper and lower control arm bushings, and panhard bar bushings.
  • Small, compact, application specific - Designed for specific truck models, No universal fit spacers required.
  • Smooth and silent - Unlike Hydro bumps, DuroBumps are whisper quiet on contact.
  • Premium bump stops - DuroBumps are proudly made in the USA from the highest quality raw materials.
  • Provided mounting hardware - JIS 10.9 zinc-coated hex head metric bolts and single-use thread locker are provided with every set of DuroBumps, insuring a secure fit.
  • Note: For off-road use only. By installing these aftermarket bump stops on your vehicle, the user assumes all risk and liability. DuroBumps are not designed for towing applications. For further information, click here. Seller will not be held liable for any damages or loss associated with the installation or use of this product for any reason.

0 -3 inch lift (Non-Long Travel) (recommended for OEM size rear shock, equivalent to OEM size bump stop) 1 inch @ 1500 lbs Size: 3.75 dia. x 3.5 in. (ea.) Weight: 36 oz. / 1.5 lbs. (set) Part DBR354R: Rear Bump Stops
What’s included:
(2) Two 3.5 inch rear DuroBumps
(2) Two JIS 10.9 M8-1.25 50 mm flange bolt
(1) Single-use medium thread locker
(1) One Free sticker
Tools required:
• Jack and jack stands
• 12 mm socket wrench
• 19 mm deep socket wrench or lug wrench
• Scraper or wire brush to clean debris
• Torque wrench

Step 1: Following vehicle manufacturer recommendations, use a properly rated jack. Lift the rear of the truck with floor jack and support the frame rails with jack stands. Remove rear wheels.
Be sure to use jack stands!
Step 2: Remove the OEM bump stop located on the frame rail above the rear axle tube, using a 12 mm deep socket.
Step 3: Use a scraper or wire brush to clean any mud/debris from the frame.
Step 4: Insert the flange bolt into the mounting hole of the DuroBumps and apply provided thread locker on the threads of the bolt. Mount DuroBumps in OEM location using a 12 mm socket wrench until snug (10 - 12 ft. lbs.). Do not over-tighten bolt.
Step 5: Repeat steps 2 - 4 on the other side.
Step 6: Reinstall wheels and lower vehicle back to the ground. Torque lug nuts to factory specifications.
Now go hit some trails or cruise the mall … whatever you're into!