Collection:

EimKeith

16 products
Regular Price $93.50
Sale Price $93.50
Regular Price
Unit price
per 
Built by: eimkeith (t4r.org) This Panhard Correction Kit (PCK) returns the Panhard bar to horizontal (per original design), eliminates the need for an aftermarket adjustable Panhard bar to recente...
Regular Price $98.20
Sale Price $98.20
Regular Price
Unit price
per 
Built by: EimKeith In stock and ready to ship This Panhard Correction Kit returns the Panhard bar to horizontal (per original design), eliminates the need for an aftermarket adjustable Panhard ba...
Regular Price $36.50
Sale Price $36.50
Regular Price
Unit price
per 
Built by: eimkeith (t4r.org)In stock and ready to shipStrut Tower Reinforcement:-3/16″ thick upper mount reinforcement plates ( – for when you bottom out that same expensive Coilover because your b...
Regular Price $129.20
Sale Price $129.20
Regular Price
Unit price
per 
If you’re wheeling your 3rd gen you’re eventually going to beef up your links. Then due to the extreme angles they find themselves in, those beefy short links are going to start bending your link m...
Regular Price $139.10
Sale Price $139.10
Regular Price
Unit price
per 
After seeing multiple incidences of failure at the ball joint end of the factory 3rd gen 4Runner lower control arms, I designed a system of reinforcement plates to combat cracking from hard & r...
Regular Price $129.90
Sale Price $129.90
Regular Price
Unit price
per 
Upgrade your stock links with these 3/16" plate and self aligning EIMKEITH lower mount reinforcements.*Welding required
Regular Price $108.02
Sale Price $108.02
Regular Price
Unit price
per 
It’s designed to slide right over the factory mount & weld up, after trimming out the weird corner of the factory mount that prohibits the use of big aftermarket joints up there. That’s right,...
Regular Price $173.30
Sale Price $173.30
Regular Price
Unit price
per 
OK, so if you’ve been following this thread on T4R, you know a bunch of us 3rd gen 4Runner guys are relocating our fuel tanks from the factory location and replacing them with f150 auxiliary tanks ...
Regular Price $106.00
Sale Price $106.00
Regular Price
Unit price
per 
One of my goals for our FZJ80 is to keep a relatively low frame height while maintaining as much up-travel as I can. I'm pursuing this in stages; first a 50mm lift to get the travel benefit of lo...
Regular Price $104.00
Sale Price $104.00
Regular Price
Unit price
per 
As your lift or load levels change the rear suspension ride height changes – so your “lift height” is rarely the advertised height (unless totally unladen, in some circumstances) and your static ri...
Regular Price $98.50
Sale Price $98.50
Regular Price
Unit price
per 
The Original PCK® - Weld-on bracket kits to correct the Panhard bar angle on 2-4.5" of lift. The Panhard Correction Kit returns the panhard bar to horizontal (per the original design), eliminates t...
Regular Price $126.00
Sale Price $126.00
Regular Price
Unit price
per 
Designed out of 3/16" steel, this lower link skids are a breezy to install.  Includes: (1) Driver Specific Bracket (1) Pass Specific Bracket  (1) eimkeith Logo Decal
Regular Price $110.20
Sale Price $110.20
Regular Price
Unit price
per 
The Original PCK® - Weld-on bracket kits to correct the Panhard bar angle on 2-4.5" of lift. The Panhard Correction Kit returns the panhard bar to horizontal (per the original design), eliminates t...
Regular Price $103.50
Sale Price $103.50
Regular Price
Unit price
per 
The Original PCK® - Weld-on bracket kits to correct the Panhard bar angle on 2-4.5" of lift. The Panhard Correction Kit returns the panhard bar to horizontal (per the original design), eliminates t...
Regular Price $154.53
Sale Price $154.53
Regular Price
Unit price
per 
We've seen plenty of bent lower shock mount on the 120/150 series axles (4th & 5th gen 4Runner, FJ Cruiser, GX) when coming down hard on a rock - the factory mount is way down there and relativ...
Regular Price $151.00
Sale Price $151.00
Regular Price
Unit price
per 
This fuel tank lift kit isn't the easiest thing to install out of my product line (getting the existing tank crossmember out of the frame is tedious!) but it raises the tank 2" so it no longer han...